Why don`t we use extremely thin oils in engines
up vote
11
down vote
favorite
I understand that lower viscosity oils are way easier to pump and move around engine parts, also they form a thinner "film" on friction surfaces which could improve parts measurements precision etc.
Is it only due to increased piston rings leakage that we don't use extremely thin oils?
Are they more prone to failure in operating and high temperatures?
Are these oils easier contaminated? Maybe they are very expensive to produce???
oil engine-theory oil-viscosity
asked Nov 20 at 14:53
kokobill
376120
add a comment |
up vote
11
down vote
favorite
I understand that lower viscosity oils are way easier to pump and move around engine parts, also they form a thinner "film" on friction surfaces which could improve parts measurements precision etc.
Is it only due to increased piston rings leakage that we don't use extremely thin oils?
Are they more prone to failure in operating and high temperatures?
Are these oils easier contaminated? Maybe they are very expensive to produce???
oil engine-theory oil-viscosity
asked Nov 20 at 14:53
kokobill
376120
add a comment |
up vote
11
down vote
favorite
up vote
11
down vote
favorite
I understand that lower viscosity oils are way easier to pump and move around engine parts, also they form a thinner "film" on friction surfaces which could improve parts measurements precision etc.
Is it only due to increased piston rings leakage that we don't use extremely thin oils?
Are they more prone to failure in operating and high temperatures?
Are these oils easier contaminated? Maybe they are very expensive to produce???
oil engine-theory oil-viscosity
asked Nov 20 at 14:53
kokobill
376120
I understand that lower viscosity oils are way easier to pump and move around engine parts, also they form a thinner "film" on friction surfaces which could improve parts measurements precision etc.
Is it only due to increased piston rings leakage that we don't use extremely thin oils?
Are they more prone to failure in operating and high temperatures?
Are these oils easier contaminated? Maybe they are very expensive to produce???
oil engine-theory oil-viscosity
oil engine-theory oil-viscosity
asked Nov 20 at 14:53
kokobill
376120
asked Nov 20 at 14:53
kokobill
376120
asked Nov 20 at 14:53
kokobill
376120
asked Nov 20 at 14:53
kokobill
376120
asked Nov 20 at 14:53
kokobill
376120
376120
add a comment |
add a comment |
3 Answers
3
active
oldest
votes
up vote
16
down vote
accepted
Thin oils tend to have a very poor shear stability, especially when they are hot. The function of the oil is to protect and lubricate the engine and ancillaries (i.e. turbo chargers). In certain applications it also makes up some (where an oil cooler is employed) or all (for aircooled engines such as the Beetle) of the circulated liquid cooling system.
I'm not sure that an oil which is consistently thin and remains so once upto operating temperature exists. Most engine oils are chosen so that they will provide some protection at cold start but optimum protection when they reach their target temperature.
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
add a comment |
up vote
5
down vote
Tribology is a huge topic...
But, the thinner the oil, then the more oil in terms of volume and/or the higher pressure is needed for a given tolerance between bearing and surface.
So many things are taken into account when specifying the oil for a particular use. Operating temperature, load on the bearings, relative speed of the bearing etc etc
answered Nov 20 at 14:58
Solar Mike
16.9k21030
add a comment |
up vote
1
down vote
We are, or are starting to, for exactly the reasons you quote.
New vehicles (VAG group for example) are starting to use 0W20 oil, with 0W16-capable engines coming soon and tests being conducted with oil as thin as 0W8.
Source: MTZ worldwide 12/2018, "Potentials and Risks of Reducing Friction with Future Ultra-low-viscosity Engine Oils"
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
16
down vote
accepted
Thin oils tend to have a very poor shear stability, especially when they are hot. The function of the oil is to protect and lubricate the engine and ancillaries (i.e. turbo chargers). In certain applications it also makes up some (where an oil cooler is employed) or all (for aircooled engines such as the Beetle) of the circulated liquid cooling system.
I'm not sure that an oil which is consistently thin and remains so once upto operating temperature exists. Most engine oils are chosen so that they will provide some protection at cold start but optimum protection when they reach their target temperature.
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
add a comment |
up vote
16
down vote
accepted
Thin oils tend to have a very poor shear stability, especially when they are hot. The function of the oil is to protect and lubricate the engine and ancillaries (i.e. turbo chargers). In certain applications it also makes up some (where an oil cooler is employed) or all (for aircooled engines such as the Beetle) of the circulated liquid cooling system.
I'm not sure that an oil which is consistently thin and remains so once upto operating temperature exists. Most engine oils are chosen so that they will provide some protection at cold start but optimum protection when they reach their target temperature.
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
add a comment |
up vote
16
down vote
accepted
up vote
16
down vote
accepted
Thin oils tend to have a very poor shear stability, especially when they are hot. The function of the oil is to protect and lubricate the engine and ancillaries (i.e. turbo chargers). In certain applications it also makes up some (where an oil cooler is employed) or all (for aircooled engines such as the Beetle) of the circulated liquid cooling system.
I'm not sure that an oil which is consistently thin and remains so once upto operating temperature exists. Most engine oils are chosen so that they will provide some protection at cold start but optimum protection when they reach their target temperature.
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
Thin oils tend to have a very poor shear stability, especially when they are hot. The function of the oil is to protect and lubricate the engine and ancillaries (i.e. turbo chargers). In certain applications it also makes up some (where an oil cooler is employed) or all (for aircooled engines such as the Beetle) of the circulated liquid cooling system.
I'm not sure that an oil which is consistently thin and remains so once upto operating temperature exists. Most engine oils are chosen so that they will provide some protection at cold start but optimum protection when they reach their target temperature.
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
answered Nov 20 at 15:00
Steve Matthews
19.3k22968
19.3k22968
add a comment |
add a comment |
up vote
5
down vote
Tribology is a huge topic...
But, the thinner the oil, then the more oil in terms of volume and/or the higher pressure is needed for a given tolerance between bearing and surface.
So many things are taken into account when specifying the oil for a particular use. Operating temperature, load on the bearings, relative speed of the bearing etc etc
answered Nov 20 at 14:58
Solar Mike
16.9k21030
add a comment |
up vote
5
down vote
Tribology is a huge topic...
But, the thinner the oil, then the more oil in terms of volume and/or the higher pressure is needed for a given tolerance between bearing and surface.
So many things are taken into account when specifying the oil for a particular use. Operating temperature, load on the bearings, relative speed of the bearing etc etc
answered Nov 20 at 14:58
Solar Mike
16.9k21030
add a comment |
up vote
5
down vote
up vote
5
down vote
Tribology is a huge topic...
But, the thinner the oil, then the more oil in terms of volume and/or the higher pressure is needed for a given tolerance between bearing and surface.
So many things are taken into account when specifying the oil for a particular use. Operating temperature, load on the bearings, relative speed of the bearing etc etc
answered Nov 20 at 14:58
Solar Mike
16.9k21030
Tribology is a huge topic...
But, the thinner the oil, then the more oil in terms of volume and/or the higher pressure is needed for a given tolerance between bearing and surface.
So many things are taken into account when specifying the oil for a particular use. Operating temperature, load on the bearings, relative speed of the bearing etc etc
answered Nov 20 at 14:58
Solar Mike
16.9k21030
answered Nov 20 at 14:58
Solar Mike
16.9k21030
answered Nov 20 at 14:58
Solar Mike
16.9k21030
answered Nov 20 at 14:58
Solar Mike
16.9k21030
16.9k21030
add a comment |
add a comment |
up vote
1
down vote
We are, or are starting to, for exactly the reasons you quote.
New vehicles (VAG group for example) are starting to use 0W20 oil, with 0W16-capable engines coming soon and tests being conducted with oil as thin as 0W8.
Source: MTZ worldwide 12/2018, "Potentials and Risks of Reducing Friction with Future Ultra-low-viscosity Engine Oils"
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
up vote
1
down vote
We are, or are starting to, for exactly the reasons you quote.
New vehicles (VAG group for example) are starting to use 0W20 oil, with 0W16-capable engines coming soon and tests being conducted with oil as thin as 0W8.
Source: MTZ worldwide 12/2018, "Potentials and Risks of Reducing Friction with Future Ultra-low-viscosity Engine Oils"
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
up vote
1
down vote
up vote
1
down vote
We are, or are starting to, for exactly the reasons you quote.
New vehicles (VAG group for example) are starting to use 0W20 oil, with 0W16-capable engines coming soon and tests being conducted with oil as thin as 0W8.
Source: MTZ worldwide 12/2018, "Potentials and Risks of Reducing Friction with Future Ultra-low-viscosity Engine Oils"
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
We are, or are starting to, for exactly the reasons you quote.
New vehicles (VAG group for example) are starting to use 0W20 oil, with 0W16-capable engines coming soon and tests being conducted with oil as thin as 0W8.
Source: MTZ worldwide 12/2018, "Potentials and Risks of Reducing Friction with Future Ultra-low-viscosity Engine Oils"
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Nov 22 at 6:12
answered Nov 20 at 21:42
Tobias Weiß
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
answered Nov 20 at 21:42
Tobias Weiß
1112
answered Nov 20 at 21:42
Tobias Weiß
1112
1112
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Tobias Weiß is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f61060%2fwhy-dont-we-use-extremely-thin-oils-in-engines%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
